v1.3.1.0
----------------------------------------------------------------------------------------
CHANGES

- Windows 8 compatibility


v1.3.0.0
----------------------------------------------------------------------------------------
CHANGES

- Enable/Disable special ABS parameter ("EBD v Veh Enable", "KeepAlive_vVeh_EnableCtrl") 
  by ECU at customer version.
- Set x86 as target plattform to avoid problems at x64 systems (MSA-Box).


v1.2.1.0
----------------------------------------------------------------------------------------
CHANGES

- Change protection system (OPL 13)
  

BUG

Call: Internal (OPL 8)
Date: 18.11.09

Description:
If MSA-Box is connected to CAN bus, error frames will occur.

Error:
CAN was activated (using wrong baud rate).


v1.2.0.0
----------------------------------------------------------------------------------------
FEATURES

- Add ASR labels to program (OPL 14)
- Extendend software version/number (OPL 14)

BUG

Call: Internal (OPL 11)
Date: 06.11.09

Description:
Resizing of window hides sub tabs (Vehicle Data ABS, Vehicle Data ASR, ...)

Error:
Resizing of window was activated.


v1.1.6.0
----------------------------------------------------------------------------------------
BUG

Call: Internal (OPL 5)
Date: 06.08.08

Description:
Parameters Wheelbase, TrackFA, TrackRA show wrong units.

Error:
Wrong text (mm)

Description:
Computer with US-Format couldn't enter floating values.

Error:
US-Format handle dot as decimal separator and
this char was filtrated.

Description:
Negative values couldn't be entered.

Error:
Minus char was filtered.


v1.1.5.0
----------------------------------------------------------------------------------------
BUG

Call: Internal (OPL 4)
Date: 05.08.08

Description:
Thrown exception at step 2 of "repair bleeding" wizard.

Error:
Problems at communication whereby telegram couldn't be sent and function returned with an error. 
Application tried to access an object (MemoryObj) which didn't exist.

BUG

Call: Internal (OPL 3)
Date: 05.08.08

Description:
Parameters calWheelCircumferenceFA, calWheelCircumferenceRA, 
calDisplacementCaliperFA, calDisplacementCaliperRA show wrong units.

Error:
Wrong text

CHANGES
- Logging of invalid values


v1.1.4.0
----------------------------------------------------------------------------------------
BUG

Call: Internal
Date: 22.07.08

Description:
Values "Number of increments (trigger wheel) front axle" and "Number of increments (trigger wheel) rear axle" was shown as float value. 
That could be confusingly.

Error:
Converter used float.


Call: Internal
Date: 22.07.08

Description: 
It was possible to enter values out of range (application data).

Error:
Range was separated by dot.


v1.1.3.0
----------------------------------------------------------------------------------------
CHANGES

- Additional hints if cancel wizard
- Add finish button to wizard
- Revised sequence pictures (pump pedal)
- Automatic reconnect if communication problems occur


v1.1.2.0
----------------------------------------------------------------------------------------
BUG

Call: Internal
Date: 18.07.08

Description: 
At some system (W2K) it's possible that program stops after established connection to ECU (Ecu connected) and
will not proceed with security access and diagnostic mode.

Error:
ECU thread returned but busy flag was still set.


v1.1.1.0
----------------------------------------------------------------------------------------
BUG

Call: Internal
Date: 17.07.08

Description: 
Pump was not stopped after release/block brake.

Error:
ECU was busy so telegram was skipped.


v1.1.0.0
----------------------------------------------------------------------------------------
FEATURES

- Online/Offline mode of application
- Save/Load values 
- Protection of critical values
- Testing page 
  (includes speed sensors, brake switch, multiswitch, pressure sensor
   yaw rate acc sensor, diagnostic lights, release/block brakes, activate pump, wizard)
- Logging 


v1.0.1.0
----------------------------------------------------------------------------------------
BUG

Call: Internal
Date: 08.04.2008

Description: 
Exceptions after closing application.

Error:
After closing application, device class still fire events. This caused to a problem 
with partly destroyed view objects. The application attempt to access e.g. destroyed objects.


v1.0.0.0
----------------------------------------------------------------------------------------
Intial version